Smart eyewear OEM/ODM manufacturer · Shenzhen, China +86 19835872450 sales@cynrin.com
Radio frequency test bench used for RED pre-scan on smart glasses
DIRECTIVE 2014/53/EU · RADIO EQUIPMENT

The Radio Equipment Directive for Bluetooth smart glasses

The RED is the CE-marking engine for every wireless product sold in the EU. This page breaks its requirements into the three classic articles and the newer cybersecurity articles, maps them to the harmonised standards laboratories actually test against, and shows how the conformity assessment produces your Declaration of Conformity.

ARTICLE 3 · ESSENTIAL REQUIREMENTS

The three classic pillars of RED compliance

Every piece of radio equipment must satisfy the essential requirements. For smart glasses the engineering evidence is generated by in-house pre-scan and then formal testing on PVT-identical units.

ARTICLE 3.1(a)

Safety & health

Electrical, thermal and mechanical safety of the complete device, charger and battery under intended and reasonably foreseeable use, including protection objectives for human health and safety.

Typical standards: EN IEC 62368-1 (audio/video & ICT equipment safety); battery handling tied to cell evidence.

ARTICLE 3.1(b)

Electromagnetic compatibility

Radiated and conducted emissions stay within limits and the device has adequate immunity, so the glasses neither disturb nor are disturbed by other equipment in domestic and portable environments.

Typical standards: EN 55032 (emissions), EN 55035 (immunity) families, with radio-specific EMC standards applied to the transmitting configuration.

ARTICLE 3.2

Effective use of the radio spectrum

The 2.4 GHz Bluetooth transmitter uses spectrum efficiently — output power, spurious emissions, adaptivity and receiver behavior — avoiding harmful interference to shared bands.

Typical standard: EN 300 328 family for wideband data transmission in 2.4 GHz ISM, against the specific Bluetooth configuration shipped.

The standards editions used are named on the DoC with dates — generic "CE approved" claims are not sufficient. Because module and firmware choices move the numbers, the RF architecture and antenna design are reviewed before EVT so that pre-scan data in the CYNRIN shielded lab predicts the external result rather than discovering a design flaw in week four of the certification window.

ARTICLE 3.3 · ADDED BY DELEGATED ACT

The cybersecurity layer connected eyewear now carries

Commission Delegated Regulation (EU) 2022/30 added three classes of protection for radio equipment capable of internet communication — smart glasses included. The harmonised standards route is the EN 18031 family.

3.3(d) · Network protection

The device must not harm the network or misuse it: resilient behavior against traffic overload, controlled network connection parameters and protection against network-mediated degradation. Relevant to glasses pairing and companion-app traffic.

3.3(e) · Personal data & privacy

Where personal data is processed — companion accounts, location, imagery, voice — the device must incorporate safeguards for personal-data protection and privacy, linking technical design to GDPR obligations of the brand and app operator.

3.3(f) · Fraud prevention

Safeguards against monetary fraud for equipment enabling electronic transactions — relevant where companion apps or future services handle payments; protected credential storage and secure-update design are the evidence themes.

Applicability and the presumption-of-conformity dates run on the European Commission's published timetable; the detailed requirements and the EN 18031-1/-2/-3 mapping are on the dedicated EN 18031 cybersecurity page.
STANDARDS ROUTE

The typical RED evidence matrix for smart glasses

RequirementHarmonised standard familyWhat the laboratory examines
Safety & health (3.1a)EN IEC 62368-1Energy-source classification, thermal behavior under charge/discharge, mechanical durability relevant to safety, charger and battery protection circuits.
EMC emissions/immunity (3.1b)EN 55032 / EN 55035Radiated and conducted emissions from the complete eyewear plus electrostatic discharge, surge, radiated and conducted immunity.
EMC for radioEN 301 489 series (as applicable to configuration)EMC requirements specific to short-range radio equipment, tested with Bluetooth active in defined modes.
Radio spectrum (3.2)EN 300 328Effective radiated power, spurious emissions, frequency range, adaptivity and receiver categories for the 2.4 GHz transmitter.
Human exposure to EMFApplicable EN EMF assessment standardsEvaluation against EMF exposure limits for the face-worn operating position, using the standard's assessment method.
Cybersecurity (3.3d/e/f)EN 18031-1 / -2 / -3Asset and threat coverage, network protection, personal-data/privacy safeguards and financial-transaction protection against the shipped firmware.
Materials & environmentRoHS 2.0 / REACH (separate legislation)Restricted substances and SVHC declarations per homogeneous material, compiled into the same technical file.

Final standards editions are fixed at program kickoff against the selected SoC, module and firmware. When a listed standard is not yet harmonised in the Official Journal for a given article, the technical file documents the route used — this is exactly why the plan is written before tooling rather than inferred after test.

CONFORMITY ASSESSMENT

From pre-scan to the signed declaration

Internal pre-scan

RF, EMC and acoustic pre-compliance data captured in-house; high-risk failures fixed before external fees start.

External testing

PVT-identical samples tested by an accredited laboratory against the agreed standard editions; engineering answers technical queries.

Technical file

Reports, schematics, BOM, antenna spec, risk assessment, supplier declarations, labels and manuals compiled as the TCF.

DoC & CE mark

Brand signs the EU Declaration of Conformity, applies CE marking and places the product — with the file held ten years.

SMT production line whose PVT build supplies certification samples
WHY PVT SAMPLES MATTER

The certified unit must equal the shipped unit

The single most avoidable delay in eyewear electronics is retesting because the certified sample did not match mass production — different antenna clearance, a swapped crystal, a late battery vendor change. CYNRIN ships samples taken from the PVT pilot build, the same build that proves the production fixtures, so the laboratory certificate describes the product consumers actually receive.

Engineering changes after certification trigger a documented review: cosmetic changes do not; radio, antenna, enclosure-conductive or firmware-security changes can. That review is part of the change-control run through the quality management system.

RED FAQ

Radio Equipment Directive questions

Is the RED the only directive smart glasses need for CE marking?
It is the central directive for the radio equipment, covering safety, EMC and spectrum. The CE declaration additionally references RoHS restrictions and, where applicable, other horizontal rules; GPSR adds operator and post-market duties in parallel; battery transport is separate. A typical smart-glasses DoC therefore lists the RED plus RoHS 2.0, with the full technical file also containing REACH declarations and EN 18031 cybersecurity evidence.
Can we rely on our Bluetooth module's RED test reports?
Module evidence is a useful input — it demonstrates the radio component in a reference enclosure — but the finished glasses must still be assessed as a complete product: enclosure materials around the antenna, co-located electronics, battery and the host EMC profile all change results. The finished-device test set runs on the complete glasses, which is why even module-based programs go through formal external testing.
What is the role of a notified body under the RED?
When harmonised standards are applied in full for the articles engaged, the manufacturer can self-assess without a notified body — the standard smart-glasses path. A notified body becomes relevant when harmonised standards are not applied in full, when gaps exist, or for specific module configurations. The kickoff certification plan states explicitly whether your configuration stays on the self-assessment route.
Do firmware updates affect RED compliance?
They can. RF-parameter and security-relevant firmware changes are reviewed against the test configuration; updates that alter radio behavior or security posture may require regression evidence, and Article 3.3 cybersecurity requirements explicitly expect secure update processes. Feature-only UI changes generally do not. Programs define which firmware components are controlled parameters at the DVT gate.
How long is RED evidence valid?
The declaration and technical file are retained for ten years after the last unit is placed on the market, but evidence is not timeless: when harmonised standards are replaced, products already placed need not be recertified, while continuing production must transition to the new standards during the European Commission's transition dates. Ongoing programs receive a standards-watch note from the compliance plan so the cutover is scheduled, not surprised by.
Does RED testing cover the camera or microphone features?
The RED tests radio, EMC, safety, spectrum and now cybersecurity; it does not assess image quality or audio performance. Privacy behavior of camera and microphone features (indicator behavior, companion-app data handling) enters through the 3.3(e) personal-data protection article and, more broadly, GDPR product expectations — worth reviewing with your compliance team for wearable cameras, as noted in the claims boundary page.

Want the exact standards editions for your radio configuration?

Share the target module or SoC in the RFQ. Engineering returns the test set, standard editions, sample list and week-by-week RED schedule.

Chat on WhatsApp
Your experience on this site will be improved by allowing cookies.